[WARNING]: Could not match supplied host pattern, ignoring: unprovisioned
[WARNING]: Found variable using reserved name: hosts

PLAY [Deploy initial device configuration] *************************************

TASK [Set variables that cannot be set with VARS] ******************************
ok: [dut]
ok: [r11]
ok: [r12]
ok: [r21]
ok: [r22]
ok: [v1]
ok: [v2]
ok: [rb]

TASK [Find device readiness script] ********************************************
ok: [dut]
ok: [r11]
ok: [r12]
ok: [r21]
ok: [v1]
ok: [r22]
ok: [v2]
ok: [rb]

TASK [Wait for device to become ready] *****************************************
skipping: [dut]
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [v1]
skipping: [v2]
skipping: [rb]

TASK [Normalize config on bridge-like devices] *********************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for dut, r11, r12, r21, r22, v1, v2, rb

TASK [Figure out whether to deploy the module normalize on current device] *****
ok: [dut]
ok: [r11]
ok: [r12]
ok: [r21]
ok: [r22]
ok: [v1]
ok: [v2]
ok: [rb]

TASK [Find configuration template for normalize] *******************************
ok: [dut]
ok: [r11]
ok: [r12]
ok: [r21]
ok: [r22]
ok: [v1]
ok: [v2]
ok: [rb]

TASK [fail] ********************************************************************
skipping: [dut]
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [v1]
skipping: [v2]
skipping: [rb]

TASK [Find configuration deployment deploy_script for normalize] ***************
ok: [dut]
ok: [r11]
ok: [r12]
ok: [r21]
ok: [v1]
ok: [v2]
ok: [r22]
ok: [rb]

TASK [Print deployed configuration when running in verbose mode] ***************
skipping: [dut]
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [v1]
skipping: [v2]
skipping: [rb]

TASK [Deploy normalize configuration] ******************************************
skipping: [dut]
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [v1]
skipping: [v2]
skipping: [rb]

TASK [Deploy initial configuration] ********************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for dut, r11, r12, r21, r22, v1, v2, rb

TASK [Figure out whether to deploy the module initial on current device] *******
ok: [dut]
ok: [r11]
ok: [r12]
ok: [r21]
ok: [r22]
ok: [v1]
ok: [v2]
ok: [rb]

TASK [Find configuration template for initial] *********************************
ok: [dut]
ok: [r11]
ok: [r12]
ok: [r21]
ok: [r22]
ok: [v1]
ok: [v2]
ok: [rb]

TASK [fail] ********************************************************************
skipping: [dut]
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [v1]
skipping: [v2]
skipping: [rb]

TASK [Find configuration deployment deploy_script for initial] *****************
ok: [dut]
ok: [r11]
ok: [r12]
ok: [r21]
ok: [r22]
ok: [v2]
ok: [v1]
ok: [rb]

TASK [Print deployed configuration when running in verbose mode] ***************
ok: [dut] => 
  msg: |-
    initial configuration for dut
    =========================================
  
    updates:
  
    - path: /interface[name=system0]/subinterface[index=0]
      value:
       description: "No description"
       ipv6:
        admin-state: enable
        address:
        - ip-prefix: "2001:db8:1::1/128"
          type: "global-unicast"
  
    - path: /interface[name=ethernet-1/1]
      value:
       description: "dut ~ r11"
       subinterface:
        index: 0
        description: "dut ~ r11"
  
    - path: /interface[name=ethernet-1/1]/subinterface[index=0]
      value:
       description: "dut ~ r11"
       ipv6:
        admin-state: enable
        address:
        - ip-prefix: "2001:db8:3::1/64"
          type: "global-unicast"
        neighbor-discovery:
         learn-unsolicited: link-local
        router-advertisement:
         router-role:
          admin-state: enable             # no ipv6 nd suppress-ra
          min-advertisement-interval: 4   # Leaving this at platform default 200..600 takes too long at startup
          _annotate_min-advertisement-interval: "Reduced from platform default 200s"
          max-advertisement-interval: 5
  
    - path: /interface[name=ethernet-1/2]
      value:
       description: "dut ~ r12"
       subinterface:
        index: 0
        description: "dut ~ r12"
  
    - path: /interface[name=ethernet-1/2]/subinterface[index=0]
      value:
       description: "dut ~ r12"
       ipv6:
        admin-state: enable
        address:
        - ip-prefix: "2001:db8:3:1::1/64"
          type: "global-unicast"
        neighbor-discovery:
         learn-unsolicited: link-local
        router-advertisement:
         router-role:
          admin-state: enable             # no ipv6 nd suppress-ra
          min-advertisement-interval: 4   # Leaving this at platform default 200..600 takes too long at startup
          _annotate_min-advertisement-interval: "Reduced from platform default 200s"
          max-advertisement-interval: 5
  
    - path: /interface[name=ethernet-1/3]
      value:
       description: "dut ~ r21"
       subinterface:
        index: 0
        description: "dut ~ r21"
  
    - path: /interface[name=ethernet-1/3]/subinterface[index=0]
      value:
       description: "dut ~ r21"
       ipv6:
        admin-state: enable
        address:
        - ip-prefix: "2001:db8:3:2::1/64"
          type: "global-unicast"
        neighbor-discovery:
         learn-unsolicited: link-local
        router-advertisement:
         router-role:
          admin-state: enable             # no ipv6 nd suppress-ra
          min-advertisement-interval: 4   # Leaving this at platform default 200..600 takes too long at startup
          _annotate_min-advertisement-interval: "Reduced from platform default 200s"
          max-advertisement-interval: 5
  
    - path: /interface[name=ethernet-1/4]
      value:
       description: "dut ~ r22"
       subinterface:
        index: 0
        description: "dut ~ r22"
  
    - path: /interface[name=ethernet-1/4]/subinterface[index=0]
      value:
       description: "dut ~ r22"
       ipv6:
        admin-state: enable
        address:
        - ip-prefix: "2001:db8:3:3::1/64"
          type: "global-unicast"
        neighbor-discovery:
         learn-unsolicited: link-local
        router-advertisement:
         router-role:
          admin-state: enable             # no ipv6 nd suppress-ra
          min-advertisement-interval: 4   # Leaving this at platform default 200..600 takes too long at startup
          _annotate_min-advertisement-interval: "Reduced from platform default 200s"
          max-advertisement-interval: 5
  
    - path: /interface[name=ethernet-1/5]
      value:
       description: "dut ~ rb"
       subinterface:
        index: 0
        description: "dut ~ rb"
  
    - path: /interface[name=ethernet-1/5]/subinterface[index=0]
      value:
       description: "dut ~ rb"
       ipv6:
        admin-state: enable
        address:
        - ip-prefix: "2001:db8:3:4::1/64"
          type: "global-unicast"
        neighbor-discovery:
         learn-unsolicited: link-local
        router-advertisement:
         router-role:
          admin-state: enable             # no ipv6 nd suppress-ra
          min-advertisement-interval: 4   # Leaving this at platform default 200..600 takes too long at startup
          _annotate_min-advertisement-interval: "Reduced from platform default 200s"
          max-advertisement-interval: 5
  
    - path: /interface[name=ethernet-1/6]
      value:
       description: "dut ~ v1"
       subinterface:
        index: 0
        description: "dut ~ v1"
  
    - path: /interface[name=ethernet-1/6]/subinterface[index=0]
      value:
       description: "dut ~ v1"
       ipv6:
        admin-state: enable
        address:
        - ip-prefix: "2001:db8:3:5::1/64"
          type: "global-unicast"
        neighbor-discovery:
         learn-unsolicited: link-local
        router-advertisement:
         router-role:
          admin-state: enable             # no ipv6 nd suppress-ra
          min-advertisement-interval: 4   # Leaving this at platform default 200..600 takes too long at startup
          _annotate_min-advertisement-interval: "Reduced from platform default 200s"
          max-advertisement-interval: 5
  
    - path: /interface[name=ethernet-1/7]
      value:
       description: "dut ~ v2"
       subinterface:
        index: 0
        description: "dut ~ v2"
  
    - path: /interface[name=ethernet-1/7]/subinterface[index=0]
      value:
       description: "dut ~ v2"
       ipv6:
        admin-state: enable
        address:
        - ip-prefix: "2001:db8:3:6::1/64"
          type: "global-unicast"
        neighbor-discovery:
         learn-unsolicited: link-local
        router-advertisement:
         router-role:
          admin-state: enable             # no ipv6 nd suppress-ra
          min-advertisement-interval: 4   # Leaving this at platform default 200..600 takes too long at startup
          _annotate_min-advertisement-interval: "Reduced from platform default 200s"
          max-advertisement-interval: 5
  
  
  
    - path: /network-instance[name=default]
      value:
       type: default
       interface:
       - name: system0.0
  
    - path: /network-instance[name=default]
      value:
       type: default
       interface:
       - name: ethernet-1/1.0
    - path: /network-instance[name=default]
      value:
       type: default
       interface:
       - name: ethernet-1/2.0
    - path: /network-instance[name=default]
      value:
       type: default
       interface:
       - name: ethernet-1/3.0
    - path: /network-instance[name=default]
      value:
       type: default
       interface:
       - name: ethernet-1/4.0
    - path: /network-instance[name=default]
      value:
       type: default
       interface:
       - name: ethernet-1/5.0
  
  
  
    # TODO: vdata.rd, vdata.import/export, vdata.af
    - path: /network-instance[name=tenant]
      value:
       type: ip-vrf
       interface:
       - name: ethernet-1/6.0
    - path: /network-instance[name=tenant]
      value:
       type: ip-vrf
       interface:
       - name: ethernet-1/7.0
ok: [r11] => 
  msg: |-
    initial configuration for r11
    =========================================
    #!/bin/bash
    #
    set -e
    set -x
    #
    # Create bash profile script
    #
    cat <<SCRIPT >/root/.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)# "
    echo
    echo "Use vtysh to connect to FRR daemon"
    echo
    SCRIPT
    #
    # This is an artifact of unknown provenance that should be removed in a year or two (= 2026/2027)
    #
    # FRR controls these parameters with 'ip forwarding' and 'ipv6 forwarding' commands
    #
    sysctl -w net.ipv4.ip_forward=0
    sysctl -w net.ipv6.conf.all.forwarding=1
    #
    #
    # Get the current next hop for the default route
    #
    def_nh=$(ip route list default|awk '{ print $3 }')
    #
    # Create the management VRF and add eth0 to it
    #
    if [ ! -e /sys/devices/virtual/net/mgmt ]; then
      ip link add mgmt type vrf table 42
    fi
    ip link set mgmt up
    sysctl -qw net.ipv6.conf.eth0.keep_addr_on_down=1
    ip link set eth0 master mgmt
    #
    # Reinstall the default route if we had it before
    #
    if [[ -n "$def_nh" ]]; then
      ip route add 0.0.0.0/0 vrf mgmt via $def_nh
    fi
    #
    # Enable FRR modules (if not using containerlab bind-mounted /etc/frr/daemons)
    #
  
    # Set system defaults
    #
    # Send ARP requests from a sane source IP address
    #
    sysctl -w net.ipv4.conf.all.arp_announce=2
  
    #
    # Create loopbacks, stub and lag/bond devices
    #
    if [ ! -e /sys/class/net/lo ]; then
      if [ ! -e /sys/devices/virtual/net/lo ]; then
        ip link add lo type dummy
        ip link set dev lo up
      fi
    fi
  
    # Disable IPv6 (for IPv4-only interfaces) or SLAAC (if the device is a router)
    #
    ip link set eth1 down
    sysctl -qw net.ipv6.conf.eth1.autoconf=0
    sysctl -qw net.ipv6.conf.eth1.accept_ra=0
    ip link set dev eth1 mtu 1500
    ip link set eth1 up
  
    #
    # Add vtysh.conf file
    echo "service integrated-vtysh-config" >/etc/frr/vtysh.conf
  
    #
    # Rest of initial configuration done through VTYSH
    #
    cat >/tmp/config <<CONFIG
    hostname r11
    !
    ipv6 forwarding
    vrf mgmt
     exit-vrf
    !
    frr defaults datacenter
    !
    interface lo
     no shutdown
     ! no ip address
     ipv6 address 2001:db8:1::2/128
    !
    interface eth1
     no shutdown
     description r11 -> dut
     ! no ip address
     ipv6 address 2001:db8:3::2/64
     ipv6 nd ra-interval 5
     no ipv6 nd suppress-ra
    !
    do write
    CONFIG
    vtysh -f /tmp/config
    exit 0
ok: [r12] => 
  msg: |-
    initial configuration for r12
    =========================================
    #!/bin/bash
    #
    set -e
    set -x
    #
    # Create bash profile script
    #
    cat <<SCRIPT >/root/.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)# "
    echo
    echo "Use vtysh to connect to FRR daemon"
    echo
    SCRIPT
    #
    # This is an artifact of unknown provenance that should be removed in a year or two (= 2026/2027)
    #
    # FRR controls these parameters with 'ip forwarding' and 'ipv6 forwarding' commands
    #
    sysctl -w net.ipv4.ip_forward=0
    sysctl -w net.ipv6.conf.all.forwarding=1
    #
    #
    # Get the current next hop for the default route
    #
    def_nh=$(ip route list default|awk '{ print $3 }')
    #
    # Create the management VRF and add eth0 to it
    #
    if [ ! -e /sys/devices/virtual/net/mgmt ]; then
      ip link add mgmt type vrf table 42
    fi
    ip link set mgmt up
    sysctl -qw net.ipv6.conf.eth0.keep_addr_on_down=1
    ip link set eth0 master mgmt
    #
    # Reinstall the default route if we had it before
    #
    if [[ -n "$def_nh" ]]; then
      ip route add 0.0.0.0/0 vrf mgmt via $def_nh
    fi
    #
    # Enable FRR modules (if not using containerlab bind-mounted /etc/frr/daemons)
    #
  
    # Set system defaults
    #
    # Send ARP requests from a sane source IP address
    #
    sysctl -w net.ipv4.conf.all.arp_announce=2
  
    #
    # Create loopbacks, stub and lag/bond devices
    #
    if [ ! -e /sys/class/net/lo ]; then
      if [ ! -e /sys/devices/virtual/net/lo ]; then
        ip link add lo type dummy
        ip link set dev lo up
      fi
    fi
  
    # Disable IPv6 (for IPv4-only interfaces) or SLAAC (if the device is a router)
    #
    ip link set eth1 down
    sysctl -qw net.ipv6.conf.eth1.autoconf=0
    sysctl -qw net.ipv6.conf.eth1.accept_ra=0
    ip link set dev eth1 mtu 1500
    ip link set eth1 up
  
    #
    # Add vtysh.conf file
    echo "service integrated-vtysh-config" >/etc/frr/vtysh.conf
  
    #
    # Rest of initial configuration done through VTYSH
    #
    cat >/tmp/config <<CONFIG
    hostname r12
    !
    ipv6 forwarding
    vrf mgmt
     exit-vrf
    !
    frr defaults datacenter
    !
    interface lo
     no shutdown
     ! no ip address
     ipv6 address 2001:db8:1::3/128
    !
    interface eth1
     no shutdown
     description r12 -> dut
     ! no ip address
     ipv6 address 2001:db8:3:1::2/64
     ipv6 nd ra-interval 5
     no ipv6 nd suppress-ra
    !
    do write
    CONFIG
    vtysh -f /tmp/config
    exit 0
ok: [rb] => 
  msg: |-
    initial configuration for rb
    =========================================
    #!/bin/bash
    #
    set -e
    set -x
    #
    # Create bash profile script
    #
    cat <<SCRIPT >/root/.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)# "
    echo
    echo "Use vtysh to connect to FRR daemon"
    echo
    SCRIPT
    #
    # This is an artifact of unknown provenance that should be removed in a year or two (= 2026/2027)
    #
    # FRR controls these parameters with 'ip forwarding' and 'ipv6 forwarding' commands
    #
    sysctl -w net.ipv4.ip_forward=0
    sysctl -w net.ipv6.conf.all.forwarding=1
    #
    #
    # Get the current next hop for the default route
    #
    def_nh=$(ip route list default|awk '{ print $3 }')
    #
    # Create the management VRF and add eth0 to it
    #
    if [ ! -e /sys/devices/virtual/net/mgmt ]; then
      ip link add mgmt type vrf table 42
    fi
    ip link set mgmt up
    sysctl -qw net.ipv6.conf.eth0.keep_addr_on_down=1
    ip link set eth0 master mgmt
    #
    # Reinstall the default route if we had it before
    #
    if [[ -n "$def_nh" ]]; then
      ip route add 0.0.0.0/0 vrf mgmt via $def_nh
    fi
    #
    # Enable FRR modules (if not using containerlab bind-mounted /etc/frr/daemons)
    #
  
    # Set system defaults
    #
    # Send ARP requests from a sane source IP address
    #
    sysctl -w net.ipv4.conf.all.arp_announce=2
  
    #
    # Create loopbacks, stub and lag/bond devices
    #
    if [ ! -e /sys/class/net/lo ]; then
      if [ ! -e /sys/devices/virtual/net/lo ]; then
        ip link add lo type dummy
        ip link set dev lo up
      fi
    fi
  
    # Disable IPv6 (for IPv4-only interfaces) or SLAAC (if the device is a router)
    #
    ip link set eth1 down
    sysctl -qw net.ipv6.conf.eth1.autoconf=0
    sysctl -qw net.ipv6.conf.eth1.accept_ra=0
    ip link set dev eth1 mtu 1500
    ip link set eth1 up
  
    #
    # Add vtysh.conf file
    echo "service integrated-vtysh-config" >/etc/frr/vtysh.conf
  
    #
    # Rest of initial configuration done through VTYSH
    #
    cat >/tmp/config <<CONFIG
    hostname rb
    !
    ipv6 forwarding
    vrf mgmt
     exit-vrf
    !
    frr defaults datacenter
    !
    interface lo
     no shutdown
     ! no ip address
     ipv6 address 2001:db8:1::8/128
    !
    interface eth1
     no shutdown
     description rb -> dut
     ! no ip address
     ipv6 address 2001:db8:3:4::2/64
     ipv6 nd ra-interval 5
     no ipv6 nd suppress-ra
    !
    do write
    CONFIG
    vtysh -f /tmp/config
    exit 0
ok: [r22] => 
  msg: |-
    initial configuration for r22
    =========================================
    #!/bin/bash
    #
    set -e
    set -x
    #
    # Create bash profile script
    #
    cat <<SCRIPT >/root/.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)# "
    echo
    echo "Use vtysh to connect to FRR daemon"
    echo
    SCRIPT
    #
    # This is an artifact of unknown provenance that should be removed in a year or two (= 2026/2027)
    #
    # FRR controls these parameters with 'ip forwarding' and 'ipv6 forwarding' commands
    #
    sysctl -w net.ipv4.ip_forward=0
    sysctl -w net.ipv6.conf.all.forwarding=1
    #
    #
    # Get the current next hop for the default route
    #
    def_nh=$(ip route list default|awk '{ print $3 }')
    #
    # Create the management VRF and add eth0 to it
    #
    if [ ! -e /sys/devices/virtual/net/mgmt ]; then
      ip link add mgmt type vrf table 42
    fi
    ip link set mgmt up
    sysctl -qw net.ipv6.conf.eth0.keep_addr_on_down=1
    ip link set eth0 master mgmt
    #
    # Reinstall the default route if we had it before
    #
    if [[ -n "$def_nh" ]]; then
      ip route add 0.0.0.0/0 vrf mgmt via $def_nh
    fi
    #
    # Enable FRR modules (if not using containerlab bind-mounted /etc/frr/daemons)
    #
  
    # Set system defaults
    #
    # Send ARP requests from a sane source IP address
    #
    sysctl -w net.ipv4.conf.all.arp_announce=2
  
    #
    # Create loopbacks, stub and lag/bond devices
    #
    if [ ! -e /sys/class/net/lo ]; then
      if [ ! -e /sys/devices/virtual/net/lo ]; then
        ip link add lo type dummy
        ip link set dev lo up
      fi
    fi
  
    # Disable IPv6 (for IPv4-only interfaces) or SLAAC (if the device is a router)
    #
    ip link set eth1 down
    sysctl -qw net.ipv6.conf.eth1.autoconf=0
    sysctl -qw net.ipv6.conf.eth1.accept_ra=0
    ip link set dev eth1 mtu 1500
    ip link set eth1 up
  
    #
    # Add vtysh.conf file
    echo "service integrated-vtysh-config" >/etc/frr/vtysh.conf
  
    #
    # Rest of initial configuration done through VTYSH
    #
    cat >/tmp/config <<CONFIG
    hostname r22
    !
    ipv6 forwarding
    vrf mgmt
     exit-vrf
    !
    frr defaults datacenter
    !
    interface lo
     no shutdown
     ! no ip address
     ipv6 address 2001:db8:1::5/128
    !
    interface eth1
     no shutdown
     description r22 -> dut
     ! no ip address
     ipv6 address 2001:db8:3:3::2/64
     ipv6 nd ra-interval 5
     no ipv6 nd suppress-ra
    !
    do write
    CONFIG
    vtysh -f /tmp/config
    exit 0
ok: [r21] => 
  msg: |-
    initial configuration for r21
    =========================================
    #!/bin/bash
    #
    set -e
    set -x
    #
    # Create bash profile script
    #
    cat <<SCRIPT >/root/.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)# "
    echo
    echo "Use vtysh to connect to FRR daemon"
    echo
    SCRIPT
    #
    # This is an artifact of unknown provenance that should be removed in a year or two (= 2026/2027)
    #
    # FRR controls these parameters with 'ip forwarding' and 'ipv6 forwarding' commands
    #
    sysctl -w net.ipv4.ip_forward=0
    sysctl -w net.ipv6.conf.all.forwarding=1
    #
    #
    # Get the current next hop for the default route
    #
    def_nh=$(ip route list default|awk '{ print $3 }')
    #
    # Create the management VRF and add eth0 to it
    #
    if [ ! -e /sys/devices/virtual/net/mgmt ]; then
      ip link add mgmt type vrf table 42
    fi
    ip link set mgmt up
    sysctl -qw net.ipv6.conf.eth0.keep_addr_on_down=1
    ip link set eth0 master mgmt
    #
    # Reinstall the default route if we had it before
    #
    if [[ -n "$def_nh" ]]; then
      ip route add 0.0.0.0/0 vrf mgmt via $def_nh
    fi
    #
    # Enable FRR modules (if not using containerlab bind-mounted /etc/frr/daemons)
    #
  
    # Set system defaults
    #
    # Send ARP requests from a sane source IP address
    #
    sysctl -w net.ipv4.conf.all.arp_announce=2
  
    #
    # Create loopbacks, stub and lag/bond devices
    #
    if [ ! -e /sys/class/net/lo ]; then
      if [ ! -e /sys/devices/virtual/net/lo ]; then
        ip link add lo type dummy
        ip link set dev lo up
      fi
    fi
  
    # Disable IPv6 (for IPv4-only interfaces) or SLAAC (if the device is a router)
    #
    ip link set eth1 down
    sysctl -qw net.ipv6.conf.eth1.autoconf=0
    sysctl -qw net.ipv6.conf.eth1.accept_ra=0
    ip link set dev eth1 mtu 1500
    ip link set eth1 up
  
    #
    # Add vtysh.conf file
    echo "service integrated-vtysh-config" >/etc/frr/vtysh.conf
  
    #
    # Rest of initial configuration done through VTYSH
    #
    cat >/tmp/config <<CONFIG
    hostname r21
    !
    ipv6 forwarding
    vrf mgmt
     exit-vrf
    !
    frr defaults datacenter
    !
    interface lo
     no shutdown
     ! no ip address
     ipv6 address 2001:db8:1::4/128
    !
    interface eth1
     no shutdown
     description r21 -> dut
     ! no ip address
     ipv6 address 2001:db8:3:2::2/64
     ipv6 nd ra-interval 5
     no ipv6 nd suppress-ra
    !
    do write
    CONFIG
    vtysh -f /tmp/config
    exit 0
ok: [v2] => 
  msg: |-
    initial configuration for v2
    =========================================
    #!/bin/bash
    #
    set -e
    set -x
    #
    # Create bash profile script
    #
    cat <<SCRIPT >/root/.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)# "
    echo
    echo "Use vtysh to connect to FRR daemon"
    echo
    SCRIPT
    #
    # This is an artifact of unknown provenance that should be removed in a year or two (= 2026/2027)
    #
    # FRR controls these parameters with 'ip forwarding' and 'ipv6 forwarding' commands
    #
    sysctl -w net.ipv4.ip_forward=0
    sysctl -w net.ipv6.conf.all.forwarding=1
    #
    #
    # Get the current next hop for the default route
    #
    def_nh=$(ip route list default|awk '{ print $3 }')
    #
    # Create the management VRF and add eth0 to it
    #
    if [ ! -e /sys/devices/virtual/net/mgmt ]; then
      ip link add mgmt type vrf table 42
    fi
    ip link set mgmt up
    sysctl -qw net.ipv6.conf.eth0.keep_addr_on_down=1
    ip link set eth0 master mgmt
    #
    # Reinstall the default route if we had it before
    #
    if [[ -n "$def_nh" ]]; then
      ip route add 0.0.0.0/0 vrf mgmt via $def_nh
    fi
    #
    # Enable FRR modules (if not using containerlab bind-mounted /etc/frr/daemons)
    #
  
    # Set system defaults
    #
    # Send ARP requests from a sane source IP address
    #
    sysctl -w net.ipv4.conf.all.arp_announce=2
  
    #
    # Create loopbacks, stub and lag/bond devices
    #
    if [ ! -e /sys/class/net/lo ]; then
      if [ ! -e /sys/devices/virtual/net/lo ]; then
        ip link add lo type dummy
        ip link set dev lo up
      fi
    fi
  
    # Disable IPv6 (for IPv4-only interfaces) or SLAAC (if the device is a router)
    #
    ip link set eth1 down
    sysctl -qw net.ipv6.conf.eth1.autoconf=0
    sysctl -qw net.ipv6.conf.eth1.accept_ra=0
    ip link set dev eth1 mtu 1500
    ip link set eth1 up
  
    #
    # Add vtysh.conf file
    echo "service integrated-vtysh-config" >/etc/frr/vtysh.conf
  
    #
    # Rest of initial configuration done through VTYSH
    #
    cat >/tmp/config <<CONFIG
    hostname v2
    !
    ipv6 forwarding
    vrf mgmt
     exit-vrf
    !
    frr defaults datacenter
    !
    interface lo
     no shutdown
     ! no ip address
     ipv6 address 2001:db8:1::7/128
    !
    interface eth1
     no shutdown
     description v2 -> dut
     ! no ip address
     ipv6 address 2001:db8:3:6::2/64
     ipv6 nd ra-interval 5
     no ipv6 nd suppress-ra
    !
    do write
    CONFIG
    vtysh -f /tmp/config
    exit 0
ok: [v1] => 
  msg: |-
    initial configuration for v1
    =========================================
    #!/bin/bash
    #
    set -e
    set -x
    #
    # Create bash profile script
    #
    cat <<SCRIPT >/root/.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)# "
    echo
    echo "Use vtysh to connect to FRR daemon"
    echo
    SCRIPT
    #
    # This is an artifact of unknown provenance that should be removed in a year or two (= 2026/2027)
    #
    # FRR controls these parameters with 'ip forwarding' and 'ipv6 forwarding' commands
    #
    sysctl -w net.ipv4.ip_forward=0
    sysctl -w net.ipv6.conf.all.forwarding=1
    #
    #
    # Get the current next hop for the default route
    #
    def_nh=$(ip route list default|awk '{ print $3 }')
    #
    # Create the management VRF and add eth0 to it
    #
    if [ ! -e /sys/devices/virtual/net/mgmt ]; then
      ip link add mgmt type vrf table 42
    fi
    ip link set mgmt up
    sysctl -qw net.ipv6.conf.eth0.keep_addr_on_down=1
    ip link set eth0 master mgmt
    #
    # Reinstall the default route if we had it before
    #
    if [[ -n "$def_nh" ]]; then
      ip route add 0.0.0.0/0 vrf mgmt via $def_nh
    fi
    #
    # Enable FRR modules (if not using containerlab bind-mounted /etc/frr/daemons)
    #
  
    # Set system defaults
    #
    # Send ARP requests from a sane source IP address
    #
    sysctl -w net.ipv4.conf.all.arp_announce=2
  
    #
    # Create loopbacks, stub and lag/bond devices
    #
    if [ ! -e /sys/class/net/lo ]; then
      if [ ! -e /sys/devices/virtual/net/lo ]; then
        ip link add lo type dummy
        ip link set dev lo up
      fi
    fi
  
    # Disable IPv6 (for IPv4-only interfaces) or SLAAC (if the device is a router)
    #
    ip link set eth1 down
    sysctl -qw net.ipv6.conf.eth1.autoconf=0
    sysctl -qw net.ipv6.conf.eth1.accept_ra=0
    ip link set dev eth1 mtu 1500
    ip link set eth1 up
  
    #
    # Add vtysh.conf file
    echo "service integrated-vtysh-config" >/etc/frr/vtysh.conf
  
    #
    # Rest of initial configuration done through VTYSH
    #
    cat >/tmp/config <<CONFIG
    hostname v1
    !
    ipv6 forwarding
    vrf mgmt
     exit-vrf
    !
    frr defaults datacenter
    !
    interface lo
     no shutdown
     ! no ip address
     ipv6 address 2001:db8:1::6/128
    !
    interface eth1
     no shutdown
     description v1 -> dut
     ! no ip address
     ipv6 address 2001:db8:3:5::2/64
     ipv6 nd ra-interval 5
     no ipv6 nd suppress-ra
    !
    do write
    CONFIG
    vtysh -f /tmp/config
    exit 0

TASK [Deploy initial configuration] ********************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/srlinux.yml for dut
included: /home/pipi/net101/tools/netsim/ansible/tasks/frr/initial-clab.yml for r11, r12, r21, r22, v1, v2, rb

TASK [Generate JSON-RPC YAML configuration] ************************************
ok: [dut]

TASK [Update SRL initial node configuration (template=/home/pipi/net101/tools/netsim/ansible/templates/initial/srlinux.j2)] ***
changed: [dut]

TASK [debug] *******************************************************************
skipping: [dut]

TASK [Attempt to load VRF kernel module] ***************************************
changed: [r11 -> localhost]

TASK [Disable FRR management VRF when modprobe fails] **************************
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [v1]
skipping: [v2]
skipping: [rb]

TASK [include_tasks] ***********************************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/frr/deploy-config.yml for r11, r12, r21, r22, v1, v2, rb

TASK [template] ****************************************************************
changed: [r21]
changed: [v1]
changed: [r11]
changed: [r22]
changed: [rb]
changed: [v2]
changed: [r12]

TASK [set_fact] ****************************************************************
ok: [r12]
ok: [r21]
ok: [r22]
ok: [r11]
ok: [rb]
ok: [v1]
ok: [v2]

TASK [run /tmp/config.sh to deploy initial config from /home/pipi/net101/tools/netsim/ansible/templates/initial/frr.j2] ***
changed: [r11]
changed: [r12]
changed: [v1]
changed: [r22]
changed: [v2]
changed: [r21]
changed: [rb]

TASK [run vtysh to import initial config from /home/pipi/net101/tools/netsim/ansible/templates/initial/frr.j2] ***
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [v1]
skipping: [v2]
skipping: [rb]

PLAY [Deploy module-specific configurations] ***********************************

TASK [Set variables that cannot be set with VARS] ******************************
ok: [dut]
ok: [r11]
ok: [r12]
ok: [r21]
ok: [r22]
ok: [rb]
ok: [v2]
ok: [v1]

TASK [Deploy individual configuration modules] *********************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for dut, r11, r12, r21, r22, rb, v1, v2 => (item=routing)
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for dut, r11, r12, r21, r22, rb, v1, v2 => (item=ospf)
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for dut, r11, r12, r21, r22, rb, v1, v2 => (item=vrf)

TASK [Figure out whether to deploy the module routing on current device] *******
ok: [dut]
ok: [r11]
ok: [r12]
ok: [r21]
ok: [r22]
ok: [rb]
ok: [v1]
ok: [v2]

TASK [Find configuration template for routing] *********************************
skipping: [dut]
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [rb]
skipping: [v1]
ok: [r22]
skipping: [v2]

TASK [fail] ********************************************************************
skipping: [dut]
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [rb]
skipping: [v1]
skipping: [v2]

TASK [Find configuration deployment deploy_script for routing] *****************
skipping: [dut]
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [rb]
skipping: [v1]
skipping: [v2]
ok: [r22]

TASK [Print deployed configuration when running in verbose mode] ***************
skipping: [dut]
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [rb]
skipping: [v1]
skipping: [v2]
ok: [r22] => 
  msg: |-
    routing configuration for r22
    =========================================
    !
    !
    !
    !
    ! Global static routes
    !
    ipv6 route 2001:db8:cafe::1/128 Null0
    ipv6 route 2001:db8:cafe:1::1/128 Null0
    ipv6 route 2001:db8:cafe:2::1/128 Null0

TASK [Deploy routing configuration] ********************************************
skipping: [dut]
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [rb]
skipping: [v1]
skipping: [v2]
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/frr.yml for r22

TASK [template] ****************************************************************
changed: [r22]

TASK [set_fact] ****************************************************************
ok: [r22]

TASK [run /tmp/config.sh to deploy routing config from /home/pipi/net101/tools/netsim/ansible/templates/routing/frr.j2] ***
skipping: [r22]

TASK [run vtysh to import routing config from /home/pipi/net101/tools/netsim/ansible/templates/routing/frr.j2] ***
changed: [r22]

TASK [Figure out whether to deploy the module ospf on current device] **********
ok: [dut]
ok: [r11]
ok: [r12]
ok: [r21]
ok: [r22]
ok: [rb]
ok: [v1]
ok: [v2]

TASK [Find configuration template for ospf] ************************************
ok: [dut]
ok: [r11]
ok: [r12]
ok: [r21]
ok: [rb]
ok: [r22]
ok: [v1]
ok: [v2]

TASK [fail] ********************************************************************
skipping: [dut]
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [rb]
skipping: [v1]
skipping: [v2]

TASK [Find configuration deployment deploy_script for ospf] ********************
ok: [dut]
ok: [r11]
ok: [r12]
ok: [r21]
ok: [r22]
ok: [rb]
ok: [v2]
ok: [v1]

TASK [Print deployed configuration when running in verbose mode] ***************
ok: [dut] => 
  msg: |-
    ospf configuration for dut
    =========================================
    updates:
  
  
    - path: /network-instance[name=default]
      value:
        router-id: 10.0.0.1
        protocols:
          ospf:
            instance:
            - name: "1"
              version: ospf-v3
              address-family: ipv6-unicast
              admin-state: enable
              max-ecmp-paths: 64
              area:
              - area-id: 0.0.0.0
                interface:
                - interface-name: system0.0
                  passive: True
              - area-id: 0.0.0.11
                interface:
                - interface-name: ethernet-1/1.0
                  interface-type: "point-to-point"
                  failure-detection:
                    enable-bfd: False
              - area-id: 0.0.0.12
                interface:
                - interface-name: ethernet-1/2.0
                  interface-type: "point-to-point"
                  failure-detection:
                    enable-bfd: False
              - area-id: 0.0.0.21
                interface:
                - interface-name: ethernet-1/3.0
                  interface-type: "point-to-point"
                  failure-detection:
                    enable-bfd: False
              - area-id: 0.0.0.22
                interface:
                - interface-name: ethernet-1/4.0
                  interface-type: "point-to-point"
                  failure-detection:
                    enable-bfd: False
              - area-id: 0.0.0.0
                interface:
                - interface-name: ethernet-1/5.0
                  interface-type: "point-to-point"
                  failure-detection:
                    enable-bfd: False
           # OSPF not configured on external interface ethernet-1/6
           # OSPF not configured on external interface ethernet-1/7
ok: [r11] => 
  msg: |-
    ospf configuration for r11
    =========================================
    !
    ! OSPFv3 FRR configuration
    !
    interface lo
    !
     ipv6 ospf6 area 0.0.0.11
    !
    interface eth1
    ! r11 -> dut
     ipv6 ospf6 area 0.0.0.11
     ipv6 ospf6 network point-to-point
    !
    !
    router ospf6
     ospf6 router-id 10.0.0.2
     timers lsa min-arrival 100
     timers throttle spf 10 50 500
  
  
    exit
  
    !
    do write
ok: [r12] => 
  msg: |-
    ospf configuration for r12
    =========================================
    !
    ! OSPFv3 FRR configuration
    !
    interface lo
    !
     ipv6 ospf6 area 0.0.0.12
    !
    interface eth1
    ! r12 -> dut
     ipv6 ospf6 area 0.0.0.12
     ipv6 ospf6 network point-to-point
    !
    !
    router ospf6
     ospf6 router-id 10.0.0.3
     timers lsa min-arrival 100
     timers throttle spf 10 50 500
  
  
    exit
  
    !
    do write
ok: [v2] => 
  msg: |-
    ospf configuration for v2
    =========================================
    !
    ! OSPFv3 FRR configuration
    !
    interface lo
    !
     ipv6 ospf6 area 0.0.0.21
    !
    interface eth1
    ! v2 -> dut
     ipv6 ospf6 area 0.0.0.21
     ipv6 ospf6 network point-to-point
    !
    !
    router ospf6
     ospf6 router-id 10.0.0.7
     timers lsa min-arrival 100
     timers throttle spf 10 50 500
  
  
    exit
  
    !
    do write
ok: [r22] => 
  msg: |-
    ospf configuration for r22
    =========================================
    !
    ! OSPFv3 FRR configuration
    !
    interface lo
    !
     ipv6 ospf6 area 0.0.0.22
    !
    interface eth1
    ! r22 -> dut
     ipv6 ospf6 area 0.0.0.22
     ipv6 ospf6 network point-to-point
    !
    !
    router ospf6
     ospf6 router-id 10.0.0.5
     timers lsa min-arrival 100
     timers throttle spf 10 50 500
  
     redistribute static
  
    exit
  
    !
    do write
ok: [v1] => 
  msg: |-
    ospf configuration for v1
    =========================================
    !
    ! OSPFv3 FRR configuration
    !
    interface lo
    !
     ipv6 ospf6 area 0.0.0.11
    !
    interface eth1
    ! v1 -> dut
     ipv6 ospf6 area 0.0.0.11
     ipv6 ospf6 network point-to-point
    !
    !
    router ospf6
     ospf6 router-id 10.0.0.6
     timers lsa min-arrival 100
     timers throttle spf 10 50 500
  
  
    exit
  
    !
    do write
ok: [r21] => 
  msg: |-
    ospf configuration for r21
    =========================================
    !
    ! OSPFv3 FRR configuration
    !
    interface lo
    !
     ipv6 ospf6 area 0.0.0.21
    !
    interface eth1
    ! r21 -> dut
     ipv6 ospf6 area 0.0.0.21
     ipv6 ospf6 network point-to-point
    !
    !
    router ospf6
     ospf6 router-id 10.0.0.4
     timers lsa min-arrival 100
     timers throttle spf 10 50 500
  
  
    exit
  
    !
    do write
ok: [rb] => 
  msg: |-
    ospf configuration for rb
    =========================================
    !
    ! OSPFv3 FRR configuration
    !
    interface lo
    !
     ipv6 ospf6 area 0.0.0.0
    !
    interface eth1
    ! rb -> dut
     ipv6 ospf6 area 0.0.0.0
     ipv6 ospf6 network point-to-point
    !
    !
    router ospf6
     ospf6 router-id 10.0.0.8
     timers lsa min-arrival 100
     timers throttle spf 10 50 500
  
  
    exit
  
    !
    do write

TASK [Deploy ospf configuration] ***********************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/srlinux.yml for dut
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/frr.yml for r11, r12, r21, r22, rb, v1, v2

TASK [Generate JSON-RPC YAML configuration] ************************************
ok: [dut]

TASK [Update SRL ospf node configuration (template=/home/pipi/net101/tools/netsim/ansible/templates/ospf/srlinux.j2)] ***
changed: [dut]

TASK [debug] *******************************************************************
skipping: [dut]

TASK [template] ****************************************************************
changed: [r12]
changed: [rb]
changed: [r11]
changed: [v1]
changed: [r22]
changed: [r21]
changed: [v2]

TASK [set_fact] ****************************************************************
ok: [r11]
ok: [r12]
ok: [r21]
ok: [v2]
ok: [r22]
ok: [rb]
ok: [v1]

TASK [run /tmp/config.sh to deploy ospf config from /home/pipi/net101/tools/netsim/ansible/templates/ospf/frr.j2] ***
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [rb]
skipping: [v1]
skipping: [v2]

TASK [run vtysh to import ospf config from /home/pipi/net101/tools/netsim/ansible/templates/ospf/frr.j2] ***
changed: [rb]
changed: [r11]
changed: [r22]
changed: [r12]
changed: [r21]
changed: [v2]
changed: [v1]

TASK [Figure out whether to deploy the module vrf on current device] ***********
ok: [dut]
ok: [r11]
ok: [r12]
ok: [r21]
ok: [r22]
ok: [rb]
ok: [v1]
ok: [v2]

TASK [Find configuration template for vrf] *************************************
skipping: [r11]
skipping: [r12]
ok: [dut]
skipping: [r21]
skipping: [r22]
skipping: [rb]
skipping: [v1]
skipping: [v2]

TASK [fail] ********************************************************************
skipping: [dut]
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [rb]
skipping: [v1]
skipping: [v2]

TASK [Find configuration deployment deploy_script for vrf] *********************
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
ok: [dut]
skipping: [rb]
skipping: [v1]
skipping: [v2]

TASK [Print deployed configuration when running in verbose mode] ***************
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [rb]
skipping: [v1]
skipping: [v2]
ok: [dut] => 
  msg: |-
    vrf configuration for dut
    =========================================
  
    updates:
  
    - path: /network-instance[name=tenant]
      value:
       type: ip-vrf
  
    - path: /routing-policy/policy[name=tenant_export_ospf]
      value:
        default-action:
          policy-result: reject
        statement:
        - name: export_local
          match:
            protocol: local
          action:
            policy-result: accept
  
  
    - path: /network-instance[name=tenant]
      value:
        router-id: 10.0.0.1
        protocols:
          ospf:
            instance:
            - name: "1"
              version: ospf-v3
              address-family: ipv6-unicast
              admin-state: enable
              max-ecmp-paths: 64
              asbr: {}
              export-policy: "tenant_export_ospf"
              area:
              - area-id: 0.0.0.11
                interface:
                - interface-name: ethernet-1/6.0
                  interface-type: "point-to-point"
                  failure-detection:
                    enable-bfd: False
              - area-id: 0.0.0.21
                interface:
                - interface-name: ethernet-1/7.0
                  interface-type: "point-to-point"
                  failure-detection:
                    enable-bfd: False
  
  
    - path: /routing-policy/community-set[name=C65000_1]
      value:
       member:
       - "target:65000:1" # Single member, else matching is AND
  
    - path: /routing-policy/community-set[name=tenant_export]
      value:
       member:
       - "target:65000:1"
  
  
    - path: /network-instance[name=tenant]/protocols/bgp-vpn
      value:
       bgp-instance:
       - id: 1
         route-distinguisher:
          rd: "65000:1"
  
    - path: /network-instance[name=tenant]/inter-instance-policies
      value:
       apply-policy:
        export-policy: "tenant_vpn_export"
        import-policy: "tenant_vpn_import"
  
    - path: /routing-policy/policy[name=tenant_vpn_export]
      value:
       default-action:
        policy-result: "accept"
        bgp:
         communities:
          add: "tenant_export"
  
    - path: /routing-policy/policy[name=tenant_vpn_import]
      value:
       default-action:
        policy-result: "reject"
       statement:
       - name: 11
         match:
          bgp:
           community-set: "C65000_1"
         action:
          policy-result: "accept"

TASK [Deploy vrf configuration] ************************************************
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [rb]
skipping: [v1]
skipping: [v2]
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/srlinux.yml for dut

TASK [Generate JSON-RPC YAML configuration] ************************************
ok: [dut]

TASK [Update SRL vrf node configuration (template=/home/pipi/net101/tools/netsim/ansible/templates/vrf/srlinux.j2)] ***
changed: [dut]

TASK [debug] *******************************************************************
skipping: [dut]

PLAY [Deploy custom deployment templates] **************************************

TASK [Run custom configuration deployment scripts] *****************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-custom-config.yml for dut, r11, r12, r21, r22, v1, v2 => (item=ospf.areas)

TASK [Find configuration template] *********************************************
ok: [dut]
ok: [r11]
ok: [r12]
ok: [r21]
ok: [r22]
ok: [v1]
ok: [v2]

TASK [fail] ********************************************************************
skipping: [dut]
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [v1]
skipping: [v2]

TASK [Check is the configuration template is a file] ***************************
ok: [dut -> localhost]
ok: [r11 -> localhost]
ok: [r12 -> localhost]
ok: [r21 -> localhost]
ok: [r22 -> localhost]
ok: [v2 -> localhost]
ok: [v1 -> localhost]

TASK [fail] ********************************************************************
skipping: [dut]
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [v1]
skipping: [v2]

TASK [Process template /home/pipi/net101/tools/netsim/extra/ospf.areas/srlinux.j2 for dut] ***
skipping: [dut]
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [v1]
skipping: [v2]

TASK [Find custom configuration deployment script] *****************************
ok: [dut]
ok: [r11]
ok: [r12]
ok: [v1]
ok: [r21]
ok: [r22]
ok: [v2]

TASK [Run the configuration deployment script] *********************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/srlinux.yml for dut
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/frr.yml for r11, r12, r21, r22, v1, v2

TASK [Generate JSON-RPC YAML configuration] ************************************
ok: [dut]

TASK [Update SRL ospf.areas node configuration (template=/home/pipi/net101/tools/netsim/extra/ospf.areas/srlinux.j2)] ***
changed: [dut]

TASK [debug] *******************************************************************
skipping: [dut]

TASK [template] ****************************************************************
changed: [r12]
changed: [r11]
changed: [r21]
changed: [v1]
changed: [v2]
changed: [r22]

TASK [set_fact] ****************************************************************
ok: [r11]
ok: [r12]
ok: [r21]
ok: [r22]
ok: [v2]
ok: [v1]

TASK [run /tmp/config.sh to deploy ospf.areas config from /home/pipi/net101/tools/netsim/extra/ospf.areas/frr.j2] ***
skipping: [r11]
skipping: [r12]
skipping: [r21]
skipping: [r22]
skipping: [v1]
skipping: [v2]

TASK [run vtysh to import ospf.areas config from /home/pipi/net101/tools/netsim/extra/ospf.areas/frr.j2] ***
changed: [r11]
changed: [v1]
changed: [r21]
changed: [v2]
changed: [r12]
changed: [r22]

PLAY RECAP *********************************************************************
dut                        : ok=40   changed=4    unreachable=0    failed=0    skipped=19   rescued=0    ignored=0   
r11                        : ok=39   changed=7    unreachable=0    failed=0    skipped=23   rescued=0    ignored=0   
r12                        : ok=38   changed=6    unreachable=0    failed=0    skipped=23   rescued=0    ignored=0   
r21                        : ok=38   changed=6    unreachable=0    failed=0    skipped=23   rescued=0    ignored=0   
r22                        : ok=45   changed=8    unreachable=0    failed=0    skipped=20   rescued=0    ignored=0   
rb                         : ok=30   changed=4    unreachable=0    failed=0    skipped=19   rescued=0    ignored=0   
v1                         : ok=38   changed=6    unreachable=0    failed=0    skipped=23   rescued=0    ignored=0   
v2                         : ok=38   changed=6    unreachable=0    failed=0    skipped=23   rescued=0    ignored=0   



This lab tests numerous combinations of OSPFv3 area parameters. It currently
tests:

* Stub and NSSA areas
* Insertion of default route into stub/NSSA areas
* Suppression of inter-area routes in stub/NSSA area